- Posts: 3
- Karma: 2
- Thank you received: 0
No pressure out put RMW2.5G28
- Dan
- Topic Author
- Offline
- Fresh Boarder
Less
More
7 years 1 month ago #2140
by Dan
No pressure out put RMW2.5G28 was created by Dan
RMW2.5G28.brass head . NO pressure out put .. Eng off and no Hi side hose on it water will run through it ,start Eng water will Stop going through after 1 Min or so thermal valve will go off /on -off/on ..
I see No leaks , If I back off way off on the adj on the unloader water will start to go through but soon as you increase adjustment water will stop going through .. Thinking its the unloader frozen ,removed- all is nice and clean and free moving and No rust on spring ,O ring have No marks or cuts all looks good .
Open for a Fix ??
I see No leaks , If I back off way off on the adj on the unloader water will start to go through but soon as you increase adjustment water will stop going through .. Thinking its the unloader frozen ,removed- all is nice and clean and free moving and No rust on spring ,O ring have No marks or cuts all looks good .
Open for a Fix ??
Please Log in or Create an account to join the conversation.
- MTR-Admin
- Offline
- Administrator
Less
More
- Posts: 1196
- Karma: 15
- Thank you received: 95
7 years 1 month ago #2146
by MTR-Admin
Replied by MTR-Admin on topic No pressure out put RMW2.5G28
Thanks for the post!
If the thermal relief is open and leaking, I'd remove it and plug the hole with a pipe plug to test the pump to see if it will make pressure. If the pump works then I'd just replace the relief valve.
- MTR
If the thermal relief is open and leaking, I'd remove it and plug the hole with a pipe plug to test the pump to see if it will make pressure. If the pump works then I'd just replace the relief valve.
- MTR
Please Log in or Create an account to join the conversation.
- Dan
- Topic Author
- Offline
- Fresh Boarder
Less
More
- Posts: 3
- Karma: 2
- Thank you received: 0
7 years 1 month ago - 7 years 1 month ago #2147
by Dan
Replied by Dan on topic No pressure out put RMW2.5G28
You have a Good Point but in my case that was not the issues .. I found the Injector ( #41 in the parts breakdown) came lose .Now to fig if any internal damage was done to head built in seat for shutter #38
Last edit: 7 years 1 month ago by Dan.
Please Log in or Create an account to join the conversation.
- Apwdistributing
- Offline
- Fresh Boarder
Less
More
- Posts: 1
- Karma: 1
- Thank you received: 0
6 years 10 months ago #2222
by Apwdistributing
Replied by Apwdistributing on topic No pressure out put RMW2.5G28
It’s very common for this to happen on the RMW pumps. The jet valve behind the injector gets stuck and stops the flow and when this happens it often times damages the check valves.
Try taking it apart and cleaning or get a new pump
Try taking it apart and cleaning or get a new pump
Please Log in or Create an account to join the conversation.
- serlyinmartini
- Offline
- Fresh Boarder
Less
More
- Posts: 1
- Thank you received: 0
6 years 2 months ago - 6 years 1 month ago #2461
by serlyinmartini
Replied by serlyinmartini on topic No pressure out put RMW2.5G28
Please be aware that this RMW2.5G28-EZ-SX pump from Annovi Reverberi is rotated 180 degrees, for mounting under your pressure washer Please see your units repair manual to determine if this is the correct mounting for your machine.
The RMW2.5G28-EZ-SX pump from Annovi Reverberi has the the following specifications:\
The unit is a Vertical Mount with Gas Flange 3-7 HP
Max. Volume on this pump is 2.5 GPM
Max. Discharge Pressure of this unit is 2,800 PSI
Max. Pump Speed on the RMW SX is 3,400 RPM
Shaft Diameter for mounting measures 7/8” Hollow
Built In unloader and chemical injector come standard on this pump
Built In easy start valve is also standard on this unit.
Maximum Horsepower Requirements to work this pump is 6.5 GHP
Inlet Port on the unit measures 3/4″ FGH (garden hose)
Outlet Port has a measurement of 22mm (Twist Connect)
Brass manifold for long life.
Stainless steel plungers built to make this pump last.
Pump comes filled with oil for quick step up and use.
The RMW2.5G28-EZ-SX pump from Annovi Reverberi has the the following specifications:\
The unit is a Vertical Mount with Gas Flange 3-7 HP
Max. Volume on this pump is 2.5 GPM
Max. Discharge Pressure of this unit is 2,800 PSI
Max. Pump Speed on the RMW SX is 3,400 RPM
Shaft Diameter for mounting measures 7/8” Hollow
Built In unloader and chemical injector come standard on this pump
Built In easy start valve is also standard on this unit.
Maximum Horsepower Requirements to work this pump is 6.5 GHP
Inlet Port on the unit measures 3/4″ FGH (garden hose)
Outlet Port has a measurement of 22mm (Twist Connect)
Brass manifold for long life.
Stainless steel plungers built to make this pump last.
Pump comes filled with oil for quick step up and use.
Last edit: 6 years 1 month ago by MTR-Admin. Reason: spelling mistake
Please Log in or Create an account to join the conversation.
- jamespal007
- Offline
- Fresh Boarder
Less
More
- Posts: 1
- Thank you received: 0
6 years 1 month ago - 6 years 1 month ago #2496
by jamespal007
Replied by jamespal007 on topic No pressure out put RMW2.5G28
Thank you so much, buddy, I am going for this product after reading your post I am ready to purchase it.
Last edit: 6 years 1 month ago by MTR-Admin.
Please Log in or Create an account to join the conversation.
Moderators: MTR-Admin
Time to create page: 0.093 seconds